How to Balance Radiators: A Step-by-Step Guide
In short: to balance radiators, you open every radiator fully, note which ones heat up first, then turn the lockshield valve down on the fastest radiators and leave it further open on the slowest, until each radiator loses about 12°C between the pipe going in and the pipe coming out. It takes a couple of hours, most of it waiting, and you need a lockshield key or adjustable spanner and ideally a thermometer.
One radiator still cold after all this? See our central heating and radiator repairs in Mill Hill. Last checked: 20 November 2026. This guide covers radiator valves only. It does not cover boiler settings or anything on the gas side of a heating system.
On this page
- How do you balance radiators?
- Do my radiators need bleeding or balancing?
- What do you need before you start?
- How to balance radiators step by step
- Can you balance radiators without a thermometer?
- How do you balance radiators in a large house or upstairs and downstairs?
- Bigger houses in Mill Hill, London NW7: why the far rooms run cold
- When should you stop and call someone?
- Frequently asked questions
How do you balance radiators?
You balance radiators by setting how much hot water each one is allowed to take, using the lockshield valve, so the radiator nearest the boiler stops hogging the flow and the furthest one gets its share. Screwfix’s guide explains that water reaches the radiator nearest the boiler far more easily than the one furthest away, so without adjustment the nearest radiator takes most of the heat (Screwfix — how to balance radiators).
The lockshield is the valve at the opposite end from the one you turn every day. It usually has a plain plastic cap rather than a numbered head, and it is meant to be set once and left alone. Balancing is simply setting it properly on every radiator in the house, in order.
Do my radiators need bleeding or balancing?
Bleeding fixes one radiator with air trapped in it; balancing fixes a house where some radiators heat up quickly and others slowly or barely at all. If a radiator is cold at the top and gurgles, that is air, and bleeding is the first thing to try. If every radiator is free of air but the rooms nearest the boiler are hot long before the far rooms, the system is out of balance.
We have a separate guide for bleeding, including what a cold bottom and black water mean: radiator cold at the bottom? That is sludge, not air. Bleed first, then balance, because air in a radiator will throw off every temperature reading you take.
What do you need before you start?
You need a lockshield valve key or an adjustable spanner, a flathead screwdriver for stubborn valve caps, a radiator bleed key, an old towel, and a thermometer. A clip-on pipe thermometer or an infrared thermometer is the easiest to use; Screwfix recommends a non-contact one.
- Paper and a pen, to list your radiators in the order they heat up.
- Someone to help, if the house is large. Viessmann suggests a second person so you are not running between floors while the radiators warm up.
- A dry day when you can have the heating off for a while. The system has to cool down completely between rounds.
- Your heated towel rails on the list too. They sit on the same system and are balanced the same way.
How to balance radiators step by step
The order below follows the method in the Screwfix guide and the Viessmann guide. Give each radiator time to settle after every adjustment; the most common mistake is reading the temperature too soon.
- Turn the heating off and let every radiator go cold.
- Bleed every radiator, including towel rails, so air does not distort the readings.
- Open everything. Take the cap off each lockshield and open it fully anticlockwise. Turn every thermostatic radiator valve (TRV) to its highest setting, including smart TRVs.
- Find the order. Turn the heating on and write down which radiator gets warm first, second, third and so on. The ones nearest the boiler are usually first.
- Turn the heating off again and let the system cool.
- Start with the fastest radiator. Close its lockshield completely, then open it by about a quarter of a turn. Turn the heating back on.
- Measure. When it is fully warm, take the temperature of the pipe going into the radiator and the pipe coming out. Adjust the lockshield until the difference is about 12°C. Open it a little to narrow the gap, close it a little to widen it.
- Repeat down the list. Move to the second-fastest radiator and do the same. Each radiator further from the boiler will usually need its lockshield open a little more than the one before.
- Put the caps back on and set your TRVs back to normal.
Why 12°C? Screwfix explains that a drop of about 12 degrees across each radiator is the target for even heat distribution and efficient heat transfer. Treat it as a target, not an exact figure.
Can you balance radiators without a thermometer?
Yes, roughly, by counting turns and checking by hand. Close the lockshield on the fastest radiator and open it about a quarter of a turn, then give each radiator further along the list a little more, so the furthest ones end up the most open. Viessmann’s guide describes the same principle: radiators furthest away may need opening more than those closest to the boiler.
Check by hand after the heating has run for a while. If the near rooms are still hot well before the far ones, close the nearest lockshields slightly more and try again. It is slower and less exact than using a thermometer, but it often fixes a cold back bedroom.
How do you balance radiators in a large house or upstairs and downstairs?
In a large house, you use exactly the same method, but the list is longer and the far end of it matters most. The radiators that heat up last are usually the ones furthest along the pipework, often in an extension, a loft room or the far end of the first floor. Their lockshields stay the most open, and the radiators near the boiler, often the kitchen and hall, are turned down the most.
Two things make big houses harder. Every round of heating up and cooling down takes longer with more water in the system, and a single radiator closed down by mistake years ago can make the whole first floor look out of balance. Take the readings floor by floor and write them down, so you can undo any change that makes things worse.
Bigger houses in Mill Hill, London NW7: why the far rooms run cold
Mill Hill has a lot of the houses where balancing matters most. In the Mill Hill ward of Barnet, 2,191 of 6,920 households live in homes with four or more bedrooms, and 3,670 of 6,921 households live in a detached or semi-detached house (Census 2021, TS050 number of bedrooms and TS044 accommodation type). A long run of pipework to a fourth bedroom or a rear extension is exactly where an unbalanced system starves the last radiator.
Most of these homes heat with their own system: 5,471 of 6,924 households in the ward have mains gas only central heating (Census 2021 TS046 central heating). That means the lockshields are yours to set. In the ward, 82 households are on a district or communal heat network only. If your flat is one of them, ask your managing agent before you adjust anything, because the heat supply is not yours to change.
If you would rather not do it yourself, we balance radiators across Mill Hill, Edgware, Stanmore and the rest of the areas we cover.
When should you stop and call someone?
Stop if a lockshield valve weeps water when you turn it, if it will not move at all, or if a radiator stays cold whatever you do. Viessmann warns that leaks can occur when adjusting radiator valves, and a seized or weeping valve usually needs a new valve or gland rather than more force.
If the boiler pressure drops after bleeding, call a Gas Safe registered engineer. You can find one on the Gas Safe Register. We do not carry out that part of the job.
Do you carry out gas or boiler work? No. We are not Gas Safe registered and do not carry out gas work. We work on radiators, radiator valves and pipework.
For valves, radiators and the pipework around them, see our central heating and radiator services or our plumbing services in North West London.
Frequently asked questions
Do you need to balance radiators with thermostatic valves?
Yes. A TRV turns a radiator down once its room is warm, but it cannot push more water to a radiator the system is starving. Set the TRVs fully open while you balance with the lockshields, then set them back.
How do you know if your radiators need balancing?
Some radiators get hot quickly while others warm slowly or stay lukewarm, even though none of them has air in it. The radiators nearest the boiler being hot well before the far rooms is the classic sign.
How long does it take to balance radiators?
Usually a couple of hours for a typical house, according to Viessmann, and longer in a large one. Most of that time is waiting for the radiators to heat up and cool down between adjustments.
Does balancing radiators save money?
It can help. Viessmann says a balanced system lets the boiler run more smoothly instead of cycling on and off. The bigger gain is comfort: the far rooms warm up without you turning the whole house up.
Why 12 degrees when balancing radiators?
A drop of about 12°C between the pipe going in and the pipe coming out of each radiator is the usual target for even heat and efficient heat transfer, as Screwfix’s guide explains. Treat it as a target, not an exact rule.
Do I need a plumber to balance my radiators?
Not necessarily. It is a DIY job if you are comfortable turning valves. Call someone if a valve leaks or will not turn, or if one radiator stays cold after balancing.
How do you balance radiators with a combi boiler?
The same way: the method works on the radiator valves, not the boiler. Do not change any boiler settings. If the pressure gauge drops after bleeding, call a Gas Safe registered engineer.
Radiators still not heating evenly in North West London? Free call-out and assessment — you only pay for the work. You get a fixed written price before any work starts, and our phone is answered every day from 8am to 10pm. Contact us or see our central heating and radiator repairs in Mill Hill.
Sources read 20 November 2026: Screwfix — How to balance radiators; Viessmann UK — How to balance radiators (21 April 2023); ONS Census 2021 via Nomis, Mill Hill (Barnet) ward E05013645: TS044, TS046, TS050.